Evo-Stik Flashband Original is a self adhesive sealing bitumen strip which bonds instantly to provide a permanent watertight seal in all climates. Evo-Stik
Flashband Original is easily applied using hand pressure and a seam roller, with no requirement for special equipment for cutting, forming or fixing. Before using this product refer to the relevant Health & Safety Data Sheet.
Product overview :
Self Adhesive Flashing Tape for Roofs
Geographic availability:
Indonesia
FEATURES :
• Superior high temperature performance
characteristics
• Quick and easy application
• Bonds to a wide range of building materials
• Cost effective method of flashing, sealing and repair
• Provides lasting protection in all climates
• Safe in application, storage and transport
• Lasts up to 15 years
USES :
• Bonds to most building materials including brick, masonry, slates, concrete roof tiles, wood, metal, concrete, terracotta tiles, glass, roofing felt, rigid plastics etc.
• Applications include a large variety of original construction and maintenance situations including repairing lead flashing, sealing valley gutters, mending
leaks in drain pipes and guttering, greenhouse repairs, protecting glazing bars, protecting insulation for pipes and tanks, repairing roofing felt joints on flat
roofs.
PREPARATION :
1. Surfaces must be clean, dry and free from dust, grease, loose materials.
2. Gaps, deep hollows and depressions greater than 3mm should be filled with an appropriate filler.
3. For improved adhesion on porous or uneven surfaces, apply Evo-Stik Flashband Primer or Evo-Stik Flashband Primer SV.
4. Using a dampened brush, apply Evo-Stik Flashband Primer (or SV), according to the relevant data sheets.
5. Do not leave the Evo-Stik Flashband Primer for more than 24 hours and therefore only coat an area sufficient for covering within the working day.
6. Surfaces such as mineralised felt or textured brick may require two coats; apply the second coat when the first coat has dried.
APPLICATION :
1. Cut Evo-Stik Flashband Original to required length.
2. Remove approximately 50mm of release backing paper and carefully position the sealing strip.
3. To avoid creasing when applying Evo-Stik Flashband Original, hold the release backing paper firmly and remove it steadily from the sealing strip as the product is applied.
4. Smooth gently into position using hand pressure, only.
5. Using a seam roller or a piece of rounded wood smooth the tape to ensure good overall contact and expel any air, especially on overlaps and at edges.
6. When laying adjacent rolls, Evo-Stik Flashband Original should be overlapped by a minimum of 25mm for a watertight seal.
7. Evo-Stik Flashband Original can be over-painted with conventional decorative paints, though a little staining of the latter may occur at the edges of the strip.
8. Fully bonded Evo-Stik Flashband Original will not accommodate appreciable joint movement.
9. For small movements apply a strip of release backing, 50mm narrower than the Evo-Stik Flashband Original, along the joint prior to the application of the Evo-Stik Flashband Original.
10. For larger movement, polyethylene foam can be laid proud of the joint, so enabling the web of supported Evo-Stik Flashband Original to accept the movement.
11. Whilst Evo-Stik Flashband Original will not damage plastic sheets it is important to bear in mind the high thermal movement of these materials.
12. If long lengths of plastic are to be sealed use, 500mm lengths overlapped by 25mm to reduce the effect of the movement.
Grey Finish – 3.75 metre rolls :
194601 - 75mm x 8 rolls
194656 - 100mm x 6 rolls
194717 - 150mm x 4 rolls
194755 - 225mm x 4 rolls
194809 - 300mm x 2 rolls
Grey Finish – 10 metre rolls :
196506 - 50mm x 6 rolls
200005 - 75mm x 4 rolls
205000 - 100mm x 3 rolls
210004 - 150mm x 2 rolls
215009 - 225mm x 2 rolls
220003 - 300mm x 1 roll
225008 - 450mm x 1 roll
228504 - 600mm x 1 roll
Evo-Stik Flashband Original is a self adhesive sealing bitumen strip which bonds instantly to provide a permanent watertight seal in all climates. Evo-Stik
Flashband Original is easily applied using hand pressure and a seam roller, with no requirement for special equipment for cutting, forming or fixing. Before using this product refer to the relevant Health & Safety Data Sheet.
Product overview :
Self Adhesive Flashing Tape for Roofs
Geographic availability:
Indonesia
FEATURES :
• Superior high temperature performance
characteristics
• Quick and easy application
• Bonds to a wide range of building materials
• Cost effective method of flashing, sealing and repair
• Provides lasting protection in all climates
• Safe in application, storage and transport
• Lasts up to 15 years
USES :
• Bonds to most building materials including brick, masonry, slates, concrete roof tiles, wood, metal, concrete, terracotta tiles, glass, roofing felt, rigid plastics etc.
• Applications include a large variety of original construction and maintenance situations including repairing lead flashing, sealing valley gutters, mending
leaks in drain pipes and guttering, greenhouse repairs, protecting glazing bars, protecting insulation for pipes and tanks, repairing roofing felt joints on flat
roofs.
PREPARATION :
1. Surfaces must be clean, dry and free from dust, grease, loose materials.
2. Gaps, deep hollows and depressions greater than 3mm should be filled with an appropriate filler.
3. For improved adhesion on porous or uneven surfaces, apply Evo-Stik Flashband Primer or Evo-Stik Flashband Primer SV.
4. Using a dampened brush, apply Evo-Stik Flashband Primer (or SV), according to the relevant data sheets.
5. Do not leave the Evo-Stik Flashband Primer for more than 24 hours and therefore only coat an area sufficient for covering within the working day.
6. Surfaces such as mineralised felt or textured brick may require two coats; apply the second coat when the first coat has dried.
APPLICATION :
1. Cut Evo-Stik Flashband Original to required length.
2. Remove approximately 50mm of release backing paper and carefully position the sealing strip.
3. To avoid creasing when applying Evo-Stik Flashband Original, hold the release backing paper firmly and remove it steadily from the sealing strip as the product is applied.
4. Smooth gently into position using hand pressure, only.
5. Using a seam roller or a piece of rounded wood smooth the tape to ensure good overall contact and expel any air, especially on overlaps and at edges.
6. When laying adjacent rolls, Evo-Stik Flashband Original should be overlapped by a minimum of 25mm for a watertight seal.
7. Evo-Stik Flashband Original can be over-painted with conventional decorative paints, though a little staining of the latter may occur at the edges of the strip.
8. Fully bonded Evo-Stik Flashband Original will not accommodate appreciable joint movement.
9. For small movements apply a strip of release backing, 50mm narrower than the Evo-Stik Flashband Original, along the joint prior to the application of the Evo-Stik Flashband Original.
10. For larger movement, polyethylene foam can be laid proud of the joint, so enabling the web of supported Evo-Stik Flashband Original to accept the movement.
11. Whilst Evo-Stik Flashband Original will not damage plastic sheets it is important to bear in mind the high thermal movement of these materials.
12. If long lengths of plastic are to be sealed use, 500mm lengths overlapped by 25mm to reduce the effect of the movement.
Grey Finish – 3.75 metre rolls :
194601 - 75mm x 8 rolls
194656 - 100mm x 6 rolls
194717 - 150mm x 4 rolls
194755 - 225mm x 4 rolls
194809 - 300mm x 2 rolls
Grey Finish – 10 metre rolls :
196506 - 50mm x 6 rolls
200005 - 75mm x 4 rolls
205000 - 100mm x 3 rolls
210004 - 150mm x 2 rolls
215009 - 225mm x 2 rolls
220003 - 300mm x 1 roll
225008 - 450mm x 1 roll
228504 - 600mm x 1 roll
Evo-Stik Flashband Original is a self adhesive sealing bitumen strip which bonds instantly to provide a permanent watertight seal in all climates. Evo-Stik
Flashband Original is easily applied using hand pressure and a seam roller, with no requirement for special equipment for cutting, forming or fixing. Before using this product refer to the relevant Health & Safety Data Sheet.
Product overview :
Self Adhesive Flashing Tape for Roofs
Geographic availability:
Indonesia
FEATURES :
• Superior high temperature performance
characteristics
• Quick and easy application
• Bonds to a wide range of building materials
• Cost effective method of flashing, sealing and repair
• Provides lasting protection in all climates
• Safe in application, storage and transport
• Lasts up to 15 years
USES :
• Bonds to most building materials including brick, masonry, slates, concrete roof tiles, wood, metal, concrete, terracotta tiles, glass, roofing felt, rigid plastics etc.
• Applications include a large variety of original construction and maintenance situations including repairing lead flashing, sealing valley gutters, mending
leaks in drain pipes and guttering, greenhouse repairs, protecting glazing bars, protecting insulation for pipes and tanks, repairing roofing felt joints on flat
roofs.
PREPARATION :
1. Surfaces must be clean, dry and free from dust, grease, loose materials.
2. Gaps, deep hollows and depressions greater than 3mm should be filled with an appropriate filler.
3. For improved adhesion on porous or uneven surfaces, apply Evo-Stik Flashband Primer or Evo-Stik Flashband Primer SV.
4. Using a dampened brush, apply Evo-Stik Flashband Primer (or SV), according to the relevant data sheets.
5. Do not leave the Evo-Stik Flashband Primer for more than 24 hours and therefore only coat an area sufficient for covering within the working day.
6. Surfaces such as mineralised felt or textured brick may require two coats; apply the second coat when the first coat has dried.
APPLICATION :
1. Cut Evo-Stik Flashband Original to required length.
2. Remove approximately 50mm of release backing paper and carefully position the sealing strip.
3. To avoid creasing when applying Evo-Stik Flashband Original, hold the release backing paper firmly and remove it steadily from the sealing strip as the product is applied.
4. Smooth gently into position using hand pressure, only.
5. Using a seam roller or a piece of rounded wood smooth the tape to ensure good overall contact and expel any air, especially on overlaps and at edges.
6. When laying adjacent rolls, Evo-Stik Flashband Original should be overlapped by a minimum of 25mm for a watertight seal.
7. Evo-Stik Flashband Original can be over-painted with conventional decorative paints, though a little staining of the latter may occur at the edges of the strip.
8. Fully bonded Evo-Stik Flashband Original will not accommodate appreciable joint movement.
9. For small movements apply a strip of release backing, 50mm narrower than the Evo-Stik Flashband Original, along the joint prior to the application of the Evo-Stik Flashband Original.
10. For larger movement, polyethylene foam can be laid proud of the joint, so enabling the web of supported Evo-Stik Flashband Original to accept the movement.
11. Whilst Evo-Stik Flashband Original will not damage plastic sheets it is important to bear in mind the high thermal movement of these materials.
12. If long lengths of plastic are to be sealed use, 500mm lengths overlapped by 25mm to reduce the effect of the movement.
Grey Finish – 3.75 metre rolls :
194601 - 75mm x 8 rolls
194656 - 100mm x 6 rolls
194717 - 150mm x 4 rolls
194755 - 225mm x 4 rolls
194809 - 300mm x 2 rolls
Grey Finish – 10 metre rolls :
196506 - 50mm x 6 rolls
200005 - 75mm x 4 rolls
205000 - 100mm x 3 rolls
210004 - 150mm x 2 rolls
215009 - 225mm x 2 rolls
220003 - 300mm x 1 roll
225008 - 450mm x 1 roll
228504 - 600mm x 1 roll
Indonesia
Australia
Hong Kong SAR
Malaysia
New Zealand
Philippines
Singapore
