Biological waste produced by pharmaceutical and gene-therapy manufacturing and R & D processes is considered hazardous to human health and therefore requires inactivation before it can be safely discharged to the sewer. Common methods for performing this deactivation utilize either heat, which elevates and holds temperature to "destroy" any existing living microorganisms, or chemicals, which are injected and held at specific concentrations required to eliminate biological waste. Following inactivation, wastewater can be safely discharged to the city sewer.
Wastech’s pre-packaged Biological Waste Inactivation (Biokill) Systems are available in multiple sizes and configurations, and its BioDELTA™ Duo (biokill + pH adjustment) and BioDELTA™ Trio (biokill + pH adjustment + CIP) systems draw seamlessly from its extensive experience in skid mounted pH adjustment systems. Integrating these processes into one system ultimately saves the client money and time by combining what are normally considered two or three separate and expensive systems into one. Since the combined BioDELTA™ Duo or BioDELTA™ Trio systems are designed and fabricated as a single, integrated system there are no compatibility, interface, communication or service issues that typically arise when utilizing multiple skids from multiple vendors. Cost savings can also be enjoyed through a reduction in field installation requirements and operator manpower.
Standard Features Include:
- 316L SS or fiberglass holding tank
- 316L SS piping
- Steam heating heat exchanger (Thermal BioKill)
- Thermal retention for complete deactivation (Thermal BioKill)
- Cooling heat exchanger (Thermal BioKill)
- Single stage treatment systems
- 50, 100, 250, 500 and 1,000-gallon batch models available
- 10, 20, 30, 50 and 100 gpm continuous models available
- Alternating duplex transfer pumps with inlet strainers
- UL-Listed control panel
- NEMA 4 powder-coated steel enclosure
- PLC-based control system with color touchscreen HMI
- Dry contacts for common alarm, influent permissive, and temperature out of range
- Run permissive for remote enable/disable
- Temperature probes in process and discharge piping
- Seismic tie-down brackets
- Pumped discharge
- Out-of-Compliance prevention system
- Skid-mounted design, ready to install
- Factory-piped, wired, and tested before shipment
Biological waste produced by pharmaceutical and gene-therapy manufacturing and R & D processes is considered hazardous to human health and therefore requires inactivation before it can be safely discharged to the sewer. Common methods for performing this deactivation utilize either heat, which elevates and holds temperature to "destroy" any existing living microorganisms, or chemicals, which are injected and held at specific concentrations required to eliminate biological waste. Following inactivation, wastewater can be safely discharged to the city sewer.
Wastech’s pre-packaged Biological Waste Inactivation (Biokill) Systems are available in multiple sizes and configurations, and its BioDELTA™ Duo (biokill + pH adjustment) and BioDELTA™ Trio (biokill + pH adjustment + CIP) systems draw seamlessly from its extensive experience in skid mounted pH adjustment systems. Integrating these processes into one system ultimately saves the client money and time by combining what are normally considered two or three separate and expensive systems into one. Since the combined BioDELTA™ Duo or BioDELTA™ Trio systems are designed and fabricated as a single, integrated system there are no compatibility, interface, communication or service issues that typically arise when utilizing multiple skids from multiple vendors. Cost savings can also be enjoyed through a reduction in field installation requirements and operator manpower.
Standard Features Include:
- 316L SS or fiberglass holding tank
- 316L SS piping
- Steam heating heat exchanger (Thermal BioKill)
- Thermal retention for complete deactivation (Thermal BioKill)
- Cooling heat exchanger (Thermal BioKill)
- Single stage treatment systems
- 50, 100, 250, 500 and 1,000-gallon batch models available
- 10, 20, 30, 50 and 100 gpm continuous models available
- Alternating duplex transfer pumps with inlet strainers
- UL-Listed control panel
- NEMA 4 powder-coated steel enclosure
- PLC-based control system with color touchscreen HMI
- Dry contacts for common alarm, influent permissive, and temperature out of range
- Run permissive for remote enable/disable
- Temperature probes in process and discharge piping
- Seismic tie-down brackets
- Pumped discharge
- Out-of-Compliance prevention system
- Skid-mounted design, ready to install
- Factory-piped, wired, and tested before shipment
Biological waste produced by pharmaceutical and gene-therapy manufacturing and R & D processes is considered hazardous to human health and therefore requires inactivation before it can be safely discharged to the sewer. Common methods for performing this deactivation utilize either heat, which elevates and holds temperature to "destroy" any existing living microorganisms, or chemicals, which are injected and held at specific concentrations required to eliminate biological waste. Following inactivation, wastewater can be safely discharged to the city sewer.
Wastech’s pre-packaged Biological Waste Inactivation (Biokill) Systems are available in multiple sizes and configurations, and its BioDELTA™ Duo (biokill + pH adjustment) and BioDELTA™ Trio (biokill + pH adjustment + CIP) systems draw seamlessly from its extensive experience in skid mounted pH adjustment systems. Integrating these processes into one system ultimately saves the client money and time by combining what are normally considered two or three separate and expensive systems into one. Since the combined BioDELTA™ Duo or BioDELTA™ Trio systems are designed and fabricated as a single, integrated system there are no compatibility, interface, communication or service issues that typically arise when utilizing multiple skids from multiple vendors. Cost savings can also be enjoyed through a reduction in field installation requirements and operator manpower.
Standard Features Include:
- 316L SS or fiberglass holding tank
- 316L SS piping
- Steam heating heat exchanger (Thermal BioKill)
- Thermal retention for complete deactivation (Thermal BioKill)
- Cooling heat exchanger (Thermal BioKill)
- Single stage treatment systems
- 50, 100, 250, 500 and 1,000-gallon batch models available
- 10, 20, 30, 50 and 100 gpm continuous models available
- Alternating duplex transfer pumps with inlet strainers
- UL-Listed control panel
- NEMA 4 powder-coated steel enclosure
- PLC-based control system with color touchscreen HMI
- Dry contacts for common alarm, influent permissive, and temperature out of range
- Run permissive for remote enable/disable
- Temperature probes in process and discharge piping
- Seismic tie-down brackets
- Pumped discharge
- Out-of-Compliance prevention system
- Skid-mounted design, ready to install
- Factory-piped, wired, and tested before shipment
United States
Australia
Hong Kong SAR
Indonesia
Malaysia
New Zealand
Philippines
Singapore
