QUICSEAL 601H Tilebond Flex H is a grey or white powder adhesive composed of cement, graded fine sand, synthetic resins and specially formulated additives to be mixed with water as a thin-set tile adhesive with very good adhesion strength.
When cured, QUICSEAL 601H is water resistant and has excellent thixotropic and shrinkage control properties.
Uses
QUICSEAL 601H is suitable for bonding ceramic tiles, quarry tiles, klinker, mosaics, natural stones, etc.
- Both wall and floor;
- Internal and external areas;
- Conventional cement-sand screeds and renders;
- Drywall board and plywood which are firmly fixed;
- Existing tiled surface.
Application
To achieve good adhesion, firstly apply a thin coat of QUICSEAL 601H adhesive firmly onto the substrate using the straight edge of the trowel followed immediately with the appropriate amount of adhesive with the notch side to achieve the required thickness. The correct notched trowel size to use will depend on the type and size of the tiles.
For large sized tiles and tiles with lugs and grooves, apply a coat of QUICSEAL 601H adhesive to the back of the tiles to ensure sufficient coverage when laid.
Lay the tiles onto the adhesive and ensure that a firm pressure is applied to achieve good contact with the adhesive.
Unfavourable climatic conditions such as strong sunlight, wind and high temperature, etc. and very porous substrates may reduce the open time of the adhesive. Hence, careful checks have to be made to ensure that skinning does not occur on the surface of the adhesive before laying the tiles. If a skinning has occurred, rework the adhesive before laying the tiles.
The tiles must be adjusted within 15 minutes after laying and must be protected from rain or strong sun for at least 24 hours.
For thin bed installations
Tile joints can be grouted usually 6 to 8 hours after laying the tiles
For thick bed installations
Tile joints can be grouted approximately 24 hours after laying the tiles, depending on the absorbency.
QUICSEAL 601H Tilebond Flex H is a grey or white powder adhesive composed of cement, graded fine sand, synthetic resins and specially formulated additives to be mixed with water as a thin-set tile adhesive with very good adhesion strength.
When cured, QUICSEAL 601H is water resistant and has excellent thixotropic and shrinkage control properties.
Uses
QUICSEAL 601H is suitable for bonding ceramic tiles, quarry tiles, klinker, mosaics, natural stones, etc.
- Both wall and floor;
- Internal and external areas;
- Conventional cement-sand screeds and renders;
- Drywall board and plywood which are firmly fixed;
- Existing tiled surface.
Application
To achieve good adhesion, firstly apply a thin coat of QUICSEAL 601H adhesive firmly onto the substrate using the straight edge of the trowel followed immediately with the appropriate amount of adhesive with the notch side to achieve the required thickness. The correct notched trowel size to use will depend on the type and size of the tiles.
For large sized tiles and tiles with lugs and grooves, apply a coat of QUICSEAL 601H adhesive to the back of the tiles to ensure sufficient coverage when laid.
Lay the tiles onto the adhesive and ensure that a firm pressure is applied to achieve good contact with the adhesive.
Unfavourable climatic conditions such as strong sunlight, wind and high temperature, etc. and very porous substrates may reduce the open time of the adhesive. Hence, careful checks have to be made to ensure that skinning does not occur on the surface of the adhesive before laying the tiles. If a skinning has occurred, rework the adhesive before laying the tiles.
The tiles must be adjusted within 15 minutes after laying and must be protected from rain or strong sun for at least 24 hours.
For thin bed installations
Tile joints can be grouted usually 6 to 8 hours after laying the tiles
For thick bed installations
Tile joints can be grouted approximately 24 hours after laying the tiles, depending on the absorbency.
QUICSEAL 601H Tilebond Flex H is a grey or white powder adhesive composed of cement, graded fine sand, synthetic resins and specially formulated additives to be mixed with water as a thin-set tile adhesive with very good adhesion strength.
When cured, QUICSEAL 601H is water resistant and has excellent thixotropic and shrinkage control properties.
Uses
QUICSEAL 601H is suitable for bonding ceramic tiles, quarry tiles, klinker, mosaics, natural stones, etc.
- Both wall and floor;
- Internal and external areas;
- Conventional cement-sand screeds and renders;
- Drywall board and plywood which are firmly fixed;
- Existing tiled surface.
Application
To achieve good adhesion, firstly apply a thin coat of QUICSEAL 601H adhesive firmly onto the substrate using the straight edge of the trowel followed immediately with the appropriate amount of adhesive with the notch side to achieve the required thickness. The correct notched trowel size to use will depend on the type and size of the tiles.
For large sized tiles and tiles with lugs and grooves, apply a coat of QUICSEAL 601H adhesive to the back of the tiles to ensure sufficient coverage when laid.
Lay the tiles onto the adhesive and ensure that a firm pressure is applied to achieve good contact with the adhesive.
Unfavourable climatic conditions such as strong sunlight, wind and high temperature, etc. and very porous substrates may reduce the open time of the adhesive. Hence, careful checks have to be made to ensure that skinning does not occur on the surface of the adhesive before laying the tiles. If a skinning has occurred, rework the adhesive before laying the tiles.
The tiles must be adjusted within 15 minutes after laying and must be protected from rain or strong sun for at least 24 hours.
For thin bed installations
Tile joints can be grouted usually 6 to 8 hours after laying the tiles
For thick bed installations
Tile joints can be grouted approximately 24 hours after laying the tiles, depending on the absorbency.
Malaysia
Australia
Hong Kong SAR
Indonesia
New Zealand
Philippines
Singapore
