QUICSEAL 531 Part A + B
QUICSEAL 531 is a two component, pre-packed high performance acrylic polymer modified cement based mortar designed for all types of resurfacing, patching and repairing of concrete surface.
Part A comprise of a polymer emulsion developed from the latest latex technology. Part B comprise of a blend of special cement, specially graded fillers and additives.
Typical Uses
QUICSEAL 531 is ideal in the following areas:-
- As general resurfacing, patching and repairing of concrete surface with high vehicular traffic.
- Topping of new and old concrete floors to increase skid and wear resistance.
- Resurfacing of worn out concrete floors
- Patching and repairing of damaged concrete surfaces
- Suitable for warehouses, car parks & driveways, bus bays, concrete roads, docks, etc.
Advantages
- Pre-packed – easy to mix and apply
- Excellent waterproofing qualities
- Excellent bond strength to substrates
- Excellent abrasion and impact resistance
- High flexural and tensile strength
- Can be applied onto damp substrates (no free water on substrate)
Surface Preparation
The substrate must be clean and sound, free of dust, loose particles. Laitance, oil, grease must be removed from concrete surfaces by scabbling, grit blasting or other means.
Defective and unsound substrate has to be removed and repaired prior to application of QUICSEAL 531
Existing substrate expansion joint is to be continued through the new topping and any moving cracks should be isolated with a movement joint.
Priming
Prime the surface with QUICSEAL 607 or QUICSEAL 113 (approx. 0.2 kg per m2). Please refer to the respective product technical data for more information.
Mixing
Pour Part A (liquid) into a clean container. Slowly add Part B (powder) into the container containing Part A and mix with a low speed mechanical mixer until a homogeneous and lump-free mix is obtained.
Application
Immediately after mixing, apply well-mixed QUICSEAL 531 with a metal trowel to the primed surface at thickness of minimum 3 mm to maximum 6 mm in one layer.
For placement of more than 1 layer, sufficient curing time interval of 6-12 hours is recommended for each subsequent layer, after the previous layer completely cures and hardens.
For surfaces requiring anti-skid finish, QUICSEAL 531 can be broom swept to a desired texture approximately 3-5 minutes after application.
Curing
Consistent with cementitious toppings, it is essential to allow QUICSEAL 531 to cure naturally in ambient conditions. Where rapid drying conditions exist, such as high temperature, direct sunlight, and strong wind, QUICSEAL 531 should be protected with polythene sheet or QUICSEAL 507 Cure-shield WB to reduce premature water loss.
Allow a minimum curing time interval of 12 hours before opening up the area to vehicular traffic.
Health & Safety
Avoid eye and unnecessary skin contact, as the product is alkaline
In case of eye contact, flush with plenty of clean water and seek medical help immediately.
QUICSEAL 531 Part A + B
QUICSEAL 531 is a two component, pre-packed high performance acrylic polymer modified cement based mortar designed for all types of resurfacing, patching and repairing of concrete surface.
Part A comprise of a polymer emulsion developed from the latest latex technology. Part B comprise of a blend of special cement, specially graded fillers and additives.
Typical Uses
QUICSEAL 531 is ideal in the following areas:-
- As general resurfacing, patching and repairing of concrete surface with high vehicular traffic.
- Topping of new and old concrete floors to increase skid and wear resistance.
- Resurfacing of worn out concrete floors
- Patching and repairing of damaged concrete surfaces
- Suitable for warehouses, car parks & driveways, bus bays, concrete roads, docks, etc.
Advantages
- Pre-packed – easy to mix and apply
- Excellent waterproofing qualities
- Excellent bond strength to substrates
- Excellent abrasion and impact resistance
- High flexural and tensile strength
- Can be applied onto damp substrates (no free water on substrate)
Surface Preparation
The substrate must be clean and sound, free of dust, loose particles. Laitance, oil, grease must be removed from concrete surfaces by scabbling, grit blasting or other means.
Defective and unsound substrate has to be removed and repaired prior to application of QUICSEAL 531
Existing substrate expansion joint is to be continued through the new topping and any moving cracks should be isolated with a movement joint.
Priming
Prime the surface with QUICSEAL 607 or QUICSEAL 113 (approx. 0.2 kg per m2). Please refer to the respective product technical data for more information.
Mixing
Pour Part A (liquid) into a clean container. Slowly add Part B (powder) into the container containing Part A and mix with a low speed mechanical mixer until a homogeneous and lump-free mix is obtained.
Application
Immediately after mixing, apply well-mixed QUICSEAL 531 with a metal trowel to the primed surface at thickness of minimum 3 mm to maximum 6 mm in one layer.
For placement of more than 1 layer, sufficient curing time interval of 6-12 hours is recommended for each subsequent layer, after the previous layer completely cures and hardens.
For surfaces requiring anti-skid finish, QUICSEAL 531 can be broom swept to a desired texture approximately 3-5 minutes after application.
Curing
Consistent with cementitious toppings, it is essential to allow QUICSEAL 531 to cure naturally in ambient conditions. Where rapid drying conditions exist, such as high temperature, direct sunlight, and strong wind, QUICSEAL 531 should be protected with polythene sheet or QUICSEAL 507 Cure-shield WB to reduce premature water loss.
Allow a minimum curing time interval of 12 hours before opening up the area to vehicular traffic.
Health & Safety
Avoid eye and unnecessary skin contact, as the product is alkaline
In case of eye contact, flush with plenty of clean water and seek medical help immediately.
QUICSEAL 531 Part A + B
QUICSEAL 531 is a two component, pre-packed high performance acrylic polymer modified cement based mortar designed for all types of resurfacing, patching and repairing of concrete surface.
Part A comprise of a polymer emulsion developed from the latest latex technology. Part B comprise of a blend of special cement, specially graded fillers and additives.
Typical Uses
QUICSEAL 531 is ideal in the following areas:-
- As general resurfacing, patching and repairing of concrete surface with high vehicular traffic.
- Topping of new and old concrete floors to increase skid and wear resistance.
- Resurfacing of worn out concrete floors
- Patching and repairing of damaged concrete surfaces
- Suitable for warehouses, car parks & driveways, bus bays, concrete roads, docks, etc.
Advantages
- Pre-packed – easy to mix and apply
- Excellent waterproofing qualities
- Excellent bond strength to substrates
- Excellent abrasion and impact resistance
- High flexural and tensile strength
- Can be applied onto damp substrates (no free water on substrate)
Surface Preparation
The substrate must be clean and sound, free of dust, loose particles. Laitance, oil, grease must be removed from concrete surfaces by scabbling, grit blasting or other means.
Defective and unsound substrate has to be removed and repaired prior to application of QUICSEAL 531
Existing substrate expansion joint is to be continued through the new topping and any moving cracks should be isolated with a movement joint.
Priming
Prime the surface with QUICSEAL 607 or QUICSEAL 113 (approx. 0.2 kg per m2). Please refer to the respective product technical data for more information.
Mixing
Pour Part A (liquid) into a clean container. Slowly add Part B (powder) into the container containing Part A and mix with a low speed mechanical mixer until a homogeneous and lump-free mix is obtained.
Application
Immediately after mixing, apply well-mixed QUICSEAL 531 with a metal trowel to the primed surface at thickness of minimum 3 mm to maximum 6 mm in one layer.
For placement of more than 1 layer, sufficient curing time interval of 6-12 hours is recommended for each subsequent layer, after the previous layer completely cures and hardens.
For surfaces requiring anti-skid finish, QUICSEAL 531 can be broom swept to a desired texture approximately 3-5 minutes after application.
Curing
Consistent with cementitious toppings, it is essential to allow QUICSEAL 531 to cure naturally in ambient conditions. Where rapid drying conditions exist, such as high temperature, direct sunlight, and strong wind, QUICSEAL 531 should be protected with polythene sheet or QUICSEAL 507 Cure-shield WB to reduce premature water loss.
Allow a minimum curing time interval of 12 hours before opening up the area to vehicular traffic.
Health & Safety
Avoid eye and unnecessary skin contact, as the product is alkaline
In case of eye contact, flush with plenty of clean water and seek medical help immediately.