- Australia
Intergrain Enviropro Endure 1 Pack
Product code : 70194990-5L Designed for professional applicators, Endure 1 Pack is a water based, highly durable, clear polyurethane. Available in Matt, Satin and Gloss, it is designed to maintain the natural & colour & beauty of timber floors. Endure 1 Pack is non-yellowing, low odour and meets the VOC requirements of the Green Building Council Australia (GBCA). Application : Methods: 10mm nap microfibre roller 1. Shake the Endure 1 Pack for 1 minute or until any settled matting agent is reincorporated. Strain product. 2. Lightly sand the sealer with a worn 180 mesh screen if needed. Apply 2 coats of Endure 1 Pack using a 10mm nap roller. To improve adhesion and minimise grain raise, screen between coats with a worn 150 grit screen or 180 grit screen. 3. Note: any contaminants that appear between coats will cause inconsistencies in the final film. It is recommended to seal doors, fireplaces and windows. To increase the wear resistance, apply up to 3 coats of Endure 1 Pack. 4. On porous timbers, up to 3 coats of Endure 1 Pack can be applied to maximise the uniformity of the finish. Note: When applying this product a total of three Coats are required. 1 coat TimberSeal, then 2 coats Endure 1 Pack Surface Preparation : All surfaces must be clean, dry, free of wax, grease, dust and other contaminants. The presence of contaminants increases the possibility of rejection and delamination. New timber floors: if uneven, the surface should be sanded with coarse sandpaper. All nail holes and cracks should be filled with Intergrain Woodblend putty. Fine sand the floor, finishing with 100 grit sandpaper, then with 150 mesh screenback and vacuum thoroughly with a commercial grade vacuum cleaner. Apply 1 coat of Enviropro Timberseal or Timberseal Ultra following the label instructions. Previously coated timber: wash the floor with Enviropro Squeaky Clean as per the label instructions. To ensure adhesion, a test patch is recommended. Sand with 100 grit screen then vacuum thoroughly and tack clean with a damp rag.
Product code : 70194990-5L Designed for professional applicators, Endure 1 Pack is a water based, highly durable, clear polyurethane. Available in Matt, Satin and Gloss, it is designed to maintain the natural & colour & beauty of timber floors. Endure 1 Pack is non-yellowing, low odour and meets the VOC requirements of the Green Building Council Australia (GBCA). Application : Methods: 10mm nap microfibre roller 1. Shake the Endure 1 Pack for 1 minute or until any settled matting agent is reincorporated. Strain product. 2. Lightly sand the sealer with a worn 180 mesh screen if needed. Apply 2 coats of Endure 1 Pack using a 10mm nap roller. To improve adhesion and minimise grain raise, screen between coats with a worn 150 grit screen or 180 grit screen. 3. Note: any contaminants that appear between coats will cause inconsistencies in the final film. It is recommended to seal doors, fireplaces and windows. To increase the wear resistance, apply up to 3 coats of Endure 1 Pack. 4. On porous timbers, up to 3 coats of Endure 1 Pack can be applied to maximise the uniformity of the finish. Note: When applying this product a total of three Coats are required. 1 coat TimberSeal, then 2 coats Endure 1 Pack Surface Preparation : All surfaces must be clean, dry, free of wax, grease, dust and other contaminants. The presence of contaminants increases the possibility of rejection and delamination. New timber floors: if uneven, the surface should be sanded with coarse sandpaper. All nail holes and cracks should be filled with Intergrain Woodblend putty. Fine sand the floor, finishing with 100 grit sandpaper, then with 150 mesh screenback and vacuum thoroughly with a commercial grade vacuum cleaner. Apply 1 coat of Enviropro Timberseal or Timberseal Ultra following the label instructions. Previously coated timber: wash the floor with Enviropro Squeaky Clean as per the label instructions. To ensure adhesion, a test patch is recommended. Sand with 100 grit screen then vacuum thoroughly and tack clean with a damp rag.
Product code : 70194990-5L
Designed for professional applicators, Endure 1 Pack is a water based, highly durable, clear polyurethane. Available in Matt, Satin and Gloss, it is designed to maintain the natural & colour & beauty of timber floors. Endure 1 Pack is non-yellowing, low odour and meets the VOC requirements of the Green Building Council Australia (GBCA).
Application :
Methods: 10mm nap microfibre roller
1. Shake the Endure 1 Pack for 1 minute or until any settled matting agent is reincorporated. Strain product.
2. Lightly sand the sealer with a worn 180 mesh screen if needed. Apply 2 coats of Endure 1 Pack using a 10mm nap roller. To improve adhesion and minimise grain raise, screen between coats with a worn 150 grit screen or 180 grit screen.
3. Note: any contaminants that appear between coats will cause inconsistencies in the final film. It is recommended to seal doors, fireplaces and windows. To increase the wear resistance, apply up to 3 coats of Endure 1 Pack.
4. On porous timbers, up to 3 coats of Endure 1 Pack can be applied to maximise the uniformity of the finish.
Note: When applying this product a total of three Coats are required. 1 coat TimberSeal, then 2 coats Endure 1 Pack
Surface Preparation :
All surfaces must be clean, dry, free of wax, grease, dust and other contaminants. The presence of contaminants increases the possibility of rejection and delamination.
New timber floors: if uneven, the surface should be sanded with coarse sandpaper. All nail holes and cracks should be filled with Intergrain Woodblend putty. Fine sand the floor, finishing with 100 grit sandpaper, then with 150 mesh screenback and vacuum thoroughly with a commercial grade vacuum cleaner. Apply 1 coat of Enviropro Timberseal or Timberseal Ultra following the label instructions.
Previously coated timber: wash the floor with Enviropro Squeaky Clean as per the label instructions. To ensure adhesion, a test patch is recommended. Sand with 100 grit screen then vacuum thoroughly and tack clean with a damp rag.
Designed for professional applicators, Endure 1 Pack is a water based, highly durable, clear polyurethane. Available in Matt, Satin and Gloss, it is designed to maintain the natural & colour & beauty of timber floors. Endure 1 Pack is non-yellowing, low odour and meets the VOC requirements of the Green Building Council Australia (GBCA).
Application :
Methods: 10mm nap microfibre roller
1. Shake the Endure 1 Pack for 1 minute or until any settled matting agent is reincorporated. Strain product.
2. Lightly sand the sealer with a worn 180 mesh screen if needed. Apply 2 coats of Endure 1 Pack using a 10mm nap roller. To improve adhesion and minimise grain raise, screen between coats with a worn 150 grit screen or 180 grit screen.
3. Note: any contaminants that appear between coats will cause inconsistencies in the final film. It is recommended to seal doors, fireplaces and windows. To increase the wear resistance, apply up to 3 coats of Endure 1 Pack.
4. On porous timbers, up to 3 coats of Endure 1 Pack can be applied to maximise the uniformity of the finish.
Note: When applying this product a total of three Coats are required. 1 coat TimberSeal, then 2 coats Endure 1 Pack
Surface Preparation :
All surfaces must be clean, dry, free of wax, grease, dust and other contaminants. The presence of contaminants increases the possibility of rejection and delamination.
New timber floors: if uneven, the surface should be sanded with coarse sandpaper. All nail holes and cracks should be filled with Intergrain Woodblend putty. Fine sand the floor, finishing with 100 grit sandpaper, then with 150 mesh screenback and vacuum thoroughly with a commercial grade vacuum cleaner. Apply 1 coat of Enviropro Timberseal or Timberseal Ultra following the label instructions.
Previously coated timber: wash the floor with Enviropro Squeaky Clean as per the label instructions. To ensure adhesion, a test patch is recommended. Sand with 100 grit screen then vacuum thoroughly and tack clean with a damp rag.
Classification Code
Surespec | : |
0671-Painting
|
Speedspec | : |
09910-Painting
09211-Acrylic Texture Render
|
General Specification
Type | : | Protective |
Coverage m2/L | : | 8 |
Clean up | : | Water |
Application | : | Parquetry | Timber floors | Stairs (All interior timber) |
Sheen | : | Matt |
Size
Sizes available | : | 5L |
Technical
Fully cured | : | 7 days |
Recoat time (hours) | : | 4 |
Collection
Other Products You Might Like