Product Code :
- 999-89858 Stir-In FINE
- 999-H0005 Stir-In COARSE
- 999-H0006 Broadcast No. 36
Luxafloor® Aggregates are additives ideal for use with most Luxafloor floor coatings to provide slip resistance when required.
Benefits
- Helps prevent slips and falls
- Broadcast Aggregates can be applied to specific areas
Features :
- Packaged in pre-measured units ready for use in Luxafloor® Floor Coatings
- Three grades available
- Range of slip resistant finishes achievable
- Easy to use with stir-in or broadcast options
With Luxafloor® Broadcast Aggregate No.36
• Tougher aggregate suitable for higher traffic areas
• Ideal for thicker films and higher build coatings
Uses :
LUXAFLOOR® AGGREGATES are used where slip resistance is a requirement, such as food preparation areas, industrial laundries, pool surrounds, and processing plants.
Surface Preparation :
Refer to the prime coat technical data sheet for recommendations
Mixing :
Mix each can thoroughly using a power mixer until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX® ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF INCORRECT COLOUR. Mix the contents of both packs together thoroughly with a power mixer and let stand for 10 minutes. Box all containers before use to ensure colour consis
Application :
STIR IN AGGREGATE :
1. Once the paint has been correctly mixed and thinned, add the Stir-In Aggregate gradually using a power mixer and continue stirring until the Stir-In Aggregate is uniformly distributed through the paint (typically 5 minutes)
2. Pour mixed material into roller tray and apply as per the relevant Luxafloor® product data sheet
3. Periodically hand-stir the paint in the roller tray and in the paint can to prevent settling of the Stir-In Aggregate
BROADCAST AGGREGATE – Light Broadcast :
1. Apply the Luxafloor® Product as per the instructions on the relevant data sheet.
2. Whilst the Luxafloor® Product is still wet, scatter the Broadcast Aggregate evenly at a rate of 50g/m2
3. Lightly back-roll the surface to improve contact of the Broadcast Aggregate with the wet Luxafloor® Product
4. When dry, lightly sweep the surface to remove any loose Broadcast Aggregate
5. Apply the final coat of Luxafloor® coating system apply as per the Luxafloor® product data sheet; do not exceed the recommended spreading rate as this will bury the Aggregate and reduce slip resistance
Broadcast to Rejection :
1. Apply the Luxafloor Product as per instructions on the relevant data sheet.
2. Immediately after the product application, the Broadcast Aggregate is to be broadcast into the liquid until a uniformly dry appearance is obtained.
3. Once the coating has cured, all excess Broadcast Aggregate is to be removed by either vacuum and/or sweeping.
4. Apply a “seal coat” of the specified Luxafloor topcoat over the broadcast floor to lock in the Broadcast Aggregate.
Product Code :
- 999-89858 Stir-In FINE
- 999-H0005 Stir-In COARSE
- 999-H0006 Broadcast No. 36
Luxafloor® Aggregates are additives ideal for use with most Luxafloor floor coatings to provide slip resistance when required.
Benefits
- Helps prevent slips and falls
- Broadcast Aggregates can be applied to specific areas
Features :
- Packaged in pre-measured units ready for use in Luxafloor® Floor Coatings
- Three grades available
- Range of slip resistant finishes achievable
- Easy to use with stir-in or broadcast options
With Luxafloor® Broadcast Aggregate No.36
• Tougher aggregate suitable for higher traffic areas
• Ideal for thicker films and higher build coatings
Uses :
LUXAFLOOR® AGGREGATES are used where slip resistance is a requirement, such as food preparation areas, industrial laundries, pool surrounds, and processing plants.
Surface Preparation :
Refer to the prime coat technical data sheet for recommendations
Mixing :
Mix each can thoroughly using a power mixer until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX® ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF INCORRECT COLOUR. Mix the contents of both packs together thoroughly with a power mixer and let stand for 10 minutes. Box all containers before use to ensure colour consis
Application :
STIR IN AGGREGATE :
1. Once the paint has been correctly mixed and thinned, add the Stir-In Aggregate gradually using a power mixer and continue stirring until the Stir-In Aggregate is uniformly distributed through the paint (typically 5 minutes)
2. Pour mixed material into roller tray and apply as per the relevant Luxafloor® product data sheet
3. Periodically hand-stir the paint in the roller tray and in the paint can to prevent settling of the Stir-In Aggregate
BROADCAST AGGREGATE – Light Broadcast :
1. Apply the Luxafloor® Product as per the instructions on the relevant data sheet.
2. Whilst the Luxafloor® Product is still wet, scatter the Broadcast Aggregate evenly at a rate of 50g/m2
3. Lightly back-roll the surface to improve contact of the Broadcast Aggregate with the wet Luxafloor® Product
4. When dry, lightly sweep the surface to remove any loose Broadcast Aggregate
5. Apply the final coat of Luxafloor® coating system apply as per the Luxafloor® product data sheet; do not exceed the recommended spreading rate as this will bury the Aggregate and reduce slip resistance
Broadcast to Rejection :
1. Apply the Luxafloor Product as per instructions on the relevant data sheet.
2. Immediately after the product application, the Broadcast Aggregate is to be broadcast into the liquid until a uniformly dry appearance is obtained.
3. Once the coating has cured, all excess Broadcast Aggregate is to be removed by either vacuum and/or sweeping.
4. Apply a “seal coat” of the specified Luxafloor topcoat over the broadcast floor to lock in the Broadcast Aggregate.
Product Code :
- 999-89858 Stir-In FINE
- 999-H0005 Stir-In COARSE
- 999-H0006 Broadcast No. 36
Luxafloor® Aggregates are additives ideal for use with most Luxafloor floor coatings to provide slip resistance when required.
Benefits
- Helps prevent slips and falls
- Broadcast Aggregates can be applied to specific areas
Features :
- Packaged in pre-measured units ready for use in Luxafloor® Floor Coatings
- Three grades available
- Range of slip resistant finishes achievable
- Easy to use with stir-in or broadcast options
With Luxafloor® Broadcast Aggregate No.36
• Tougher aggregate suitable for higher traffic areas
• Ideal for thicker films and higher build coatings
Uses :
LUXAFLOOR® AGGREGATES are used where slip resistance is a requirement, such as food preparation areas, industrial laundries, pool surrounds, and processing plants.
Surface Preparation :
Refer to the prime coat technical data sheet for recommendations
Mixing :
Mix each can thoroughly using a power mixer until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX® ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF INCORRECT COLOUR. Mix the contents of both packs together thoroughly with a power mixer and let stand for 10 minutes. Box all containers before use to ensure colour consis
Application :
STIR IN AGGREGATE :
1. Once the paint has been correctly mixed and thinned, add the Stir-In Aggregate gradually using a power mixer and continue stirring until the Stir-In Aggregate is uniformly distributed through the paint (typically 5 minutes)
2. Pour mixed material into roller tray and apply as per the relevant Luxafloor® product data sheet
3. Periodically hand-stir the paint in the roller tray and in the paint can to prevent settling of the Stir-In Aggregate
BROADCAST AGGREGATE – Light Broadcast :
1. Apply the Luxafloor® Product as per the instructions on the relevant data sheet.
2. Whilst the Luxafloor® Product is still wet, scatter the Broadcast Aggregate evenly at a rate of 50g/m2
3. Lightly back-roll the surface to improve contact of the Broadcast Aggregate with the wet Luxafloor® Product
4. When dry, lightly sweep the surface to remove any loose Broadcast Aggregate
5. Apply the final coat of Luxafloor® coating system apply as per the Luxafloor® product data sheet; do not exceed the recommended spreading rate as this will bury the Aggregate and reduce slip resistance
Broadcast to Rejection :
1. Apply the Luxafloor Product as per instructions on the relevant data sheet.
2. Immediately after the product application, the Broadcast Aggregate is to be broadcast into the liquid until a uniformly dry appearance is obtained.
3. Once the coating has cured, all excess Broadcast Aggregate is to be removed by either vacuum and/or sweeping.
4. Apply a “seal coat” of the specified Luxafloor topcoat over the broadcast floor to lock in the Broadcast Aggregate.
Australia
Hong Kong SAR
Indonesia
Malaysia
New Zealand
Philippines
Singapore
