Product code :
- 776-63001 White/Light Base
- 776-63002 Deep Base
- 776-63003 Clear Base
- 776-38678 N35 Light Grey
- 976-H0153 Standard Hardener
- 976-H0227 Cold Cure Hardener
LUXAFLOOR® LGE is a high-solids, semi-gloss epoxy floor coating with excellent durability and chemical resistance against a range of solvents.
LUXAFLOOR® LGE is available in all the colours on the LUXAFLOOR® Colour Chart and can be matched to most colours in the Dulux® World of Colour range through the COLORFAST™ Tint System.
Luxafloor® High Build
Luxafloor high build range of coatings are recommended for high traffic areas where there is likely to be increased wear and tear. Products in this range have excellent durability and chemical resistance due to the high build nature of the coatings.
Benefits
- Easily transforms bare concrete floors
- Easy application by roller
- Choice of smooth or slip resistant finishes
Features :
- Excellent bond to prepared concrete floors
- Use as a finish on interior areas or as a primer for Luxafloor® PTX on exterior areas
- Available in all the colours from the Luxafloor® Colour Chart
- Cold cure hardener available
Low Gloss Two Pack Epoxy
• Primer and topcoat – exterior primer and interior topcoat
• Excellent chemical resistance
Uses :
LUXAFLOOR® LGE withstands repeated cleaning and hosing down and even withstands ponding water. LUXAFLOOR® LGE is fully compatible with LUXAFLOOR® PTX for floors that extend to areas exposed to UV.
Surface Preparation :
Concrete Floors: Concrete must be at least 28 days old before coating. Remove oil, grease and other oily contaminants with Gamlen CA 1 (according to the manufacturer’s written instructions and all safety warnings). Diamond grind, blast-track or mechanically abrade concrete floors to remove laitance, curing compounds, hardeners, sealers and/or other contaminants and to provide a concrete surface profile of CSP 2-3 per ICRI 310.2R. Remove all dust and debris by vacuum cleaning. Large cracks, voids and other surface imperfections should be filled with Luxafloor® Filler or other suitable filler/surfacer as recommended by your local Protective Coatings Representative.
Application :
Mix each can thoroughly using a power mixer until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF INCORRECT COLOUR. Mix the contents of both packs together thoroughly using a power mixer and allow to stand for 10 minutes. Box all containers before use to ensure colour consistency. Remix thoroughly before use.
Application Methods :
Brush, roller, conventional or airless spray
Product code :
- 776-63001 White/Light Base
- 776-63002 Deep Base
- 776-63003 Clear Base
- 776-38678 N35 Light Grey
- 976-H0153 Standard Hardener
- 976-H0227 Cold Cure Hardener
LUXAFLOOR® LGE is a high-solids, semi-gloss epoxy floor coating with excellent durability and chemical resistance against a range of solvents.
LUXAFLOOR® LGE is available in all the colours on the LUXAFLOOR® Colour Chart and can be matched to most colours in the Dulux® World of Colour range through the COLORFAST™ Tint System.
Luxafloor® High Build
Luxafloor high build range of coatings are recommended for high traffic areas where there is likely to be increased wear and tear. Products in this range have excellent durability and chemical resistance due to the high build nature of the coatings.
Benefits
- Easily transforms bare concrete floors
- Easy application by roller
- Choice of smooth or slip resistant finishes
Features :
- Excellent bond to prepared concrete floors
- Use as a finish on interior areas or as a primer for Luxafloor® PTX on exterior areas
- Available in all the colours from the Luxafloor® Colour Chart
- Cold cure hardener available
Low Gloss Two Pack Epoxy
• Primer and topcoat – exterior primer and interior topcoat
• Excellent chemical resistance
Uses :
LUXAFLOOR® LGE withstands repeated cleaning and hosing down and even withstands ponding water. LUXAFLOOR® LGE is fully compatible with LUXAFLOOR® PTX for floors that extend to areas exposed to UV.
Surface Preparation :
Concrete Floors: Concrete must be at least 28 days old before coating. Remove oil, grease and other oily contaminants with Gamlen CA 1 (according to the manufacturer’s written instructions and all safety warnings). Diamond grind, blast-track or mechanically abrade concrete floors to remove laitance, curing compounds, hardeners, sealers and/or other contaminants and to provide a concrete surface profile of CSP 2-3 per ICRI 310.2R. Remove all dust and debris by vacuum cleaning. Large cracks, voids and other surface imperfections should be filled with Luxafloor® Filler or other suitable filler/surfacer as recommended by your local Protective Coatings Representative.
Application :
Mix each can thoroughly using a power mixer until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF INCORRECT COLOUR. Mix the contents of both packs together thoroughly using a power mixer and allow to stand for 10 minutes. Box all containers before use to ensure colour consistency. Remix thoroughly before use.
Application Methods :
Brush, roller, conventional or airless spray
Product code :
- 776-63001 White/Light Base
- 776-63002 Deep Base
- 776-63003 Clear Base
- 776-38678 N35 Light Grey
- 976-H0153 Standard Hardener
- 976-H0227 Cold Cure Hardener
LUXAFLOOR® LGE is a high-solids, semi-gloss epoxy floor coating with excellent durability and chemical resistance against a range of solvents.
LUXAFLOOR® LGE is available in all the colours on the LUXAFLOOR® Colour Chart and can be matched to most colours in the Dulux® World of Colour range through the COLORFAST™ Tint System.
Luxafloor® High Build
Luxafloor high build range of coatings are recommended for high traffic areas where there is likely to be increased wear and tear. Products in this range have excellent durability and chemical resistance due to the high build nature of the coatings.
Benefits
- Easily transforms bare concrete floors
- Easy application by roller
- Choice of smooth or slip resistant finishes
Features :
- Excellent bond to prepared concrete floors
- Use as a finish on interior areas or as a primer for Luxafloor® PTX on exterior areas
- Available in all the colours from the Luxafloor® Colour Chart
- Cold cure hardener available
Low Gloss Two Pack Epoxy
• Primer and topcoat – exterior primer and interior topcoat
• Excellent chemical resistance
Uses :
LUXAFLOOR® LGE withstands repeated cleaning and hosing down and even withstands ponding water. LUXAFLOOR® LGE is fully compatible with LUXAFLOOR® PTX for floors that extend to areas exposed to UV.
Surface Preparation :
Concrete Floors: Concrete must be at least 28 days old before coating. Remove oil, grease and other oily contaminants with Gamlen CA 1 (according to the manufacturer’s written instructions and all safety warnings). Diamond grind, blast-track or mechanically abrade concrete floors to remove laitance, curing compounds, hardeners, sealers and/or other contaminants and to provide a concrete surface profile of CSP 2-3 per ICRI 310.2R. Remove all dust and debris by vacuum cleaning. Large cracks, voids and other surface imperfections should be filled with Luxafloor® Filler or other suitable filler/surfacer as recommended by your local Protective Coatings Representative.
Application :
Mix each can thoroughly using a power mixer until the contents are uniform. Ensure bases have been tinted to the correct colour before use. DULUX ASSUMES NO RESPONSIBILITY FOR THE APPLICATION OF INCORRECT COLOUR. Mix the contents of both packs together thoroughly using a power mixer and allow to stand for 10 minutes. Box all containers before use to ensure colour consistency. Remix thoroughly before use.
Application Methods :
Brush, roller, conventional or airless spray
Australia
Hong Kong SAR
Indonesia
Malaysia
New Zealand
Philippines
Singapore
