One-part polyurethane waterproofing membrane for horizontal applications
A one-part, liquid applied, high solids, polyurethane (PU) waterproofing membrane. It is formulated for simple, high build application to horizontal substrates. After application, the product cures through reaction with ambient humidity, forming a flexible, elastomeric membrane.
Advantages
• Seamless – liquid applied and monolithic, eliminating vulnerable joins, seams and laps
• Self-levelling – quick application
• Fully Bonded – no water tracking between membrane and substrate
• Simple Application – one-part, humidity cured. Applied by squeegee, roller or brush to horizontal surfaces
• Cold Applied – no flame or heat required for application
• Low VOC – reduced EH&S issues on site
• Flexible – long life elastomeric membrane. Accommodates normal structural movement and bridges non-structural concrete shrinkage cracks without requiring full membrane reinforcing
• Polyurethane Chemistry – free from bitumen or tar – will not bleed or stain
• External Above Ground – designed to meet the requirements of AS 4654-2012
System Components
• AQUAGARD™ M UVR – 1-part PU membrane
• AQUAGARD™ M Clear Primer – 1-part solvent based PU primer for dry cementitious, masonry, metal and timber substrates
• EPOCOTE™ F100W Clear – 2-part, water borne epoxy primer for green, damp or dry cementitious, masonry and metal substrates
• EPOCOTE™ F100W Grey – 2-part, water borne, filled epoxy primer for green, damp or dry cementitious, masonry and metal substrates, or poor quality/damaged concrete
• AQUAGARD™ M Non-Slip Top Coat – 2-part, solvent based, UV stable PU, protective top coat. Only used over exposed AQUAGARD™ M UVR membrane or in foot trafficable areas
• SILCOR® LM PU Sealant – 1-part polyurethane sealant for detailing and joint sealing
• Reinforcing PE Fabric Strip – Non-woven, needle punched polyester reinforcing fabric. For membrane reinforcement at high movement junctions
Compatibility / Adhesion
AQUAGARD™ M UVR may be applied to the following cured, stable, prepared and primed substrates:
• Concrete, blockwork, brick
• Cementitious screed, render or topping slabs
• Water resistant timber, plywood or particle board
• Metals
• Compressed fibre cement sheet (CFC)
• Cement composite sheet (CCS)
• Glass reinforced concrete (GRC)
• Rendered, aerated autoclaved concrete (AAC)
One-part polyurethane waterproofing membrane for horizontal applications
A one-part, liquid applied, high solids, polyurethane (PU) waterproofing membrane. It is formulated for simple, high build application to horizontal substrates. After application, the product cures through reaction with ambient humidity, forming a flexible, elastomeric membrane.
Advantages
• Seamless – liquid applied and monolithic, eliminating vulnerable joins, seams and laps
• Self-levelling – quick application
• Fully Bonded – no water tracking between membrane and substrate
• Simple Application – one-part, humidity cured. Applied by squeegee, roller or brush to horizontal surfaces
• Cold Applied – no flame or heat required for application
• Low VOC – reduced EH&S issues on site
• Flexible – long life elastomeric membrane. Accommodates normal structural movement and bridges non-structural concrete shrinkage cracks without requiring full membrane reinforcing
• Polyurethane Chemistry – free from bitumen or tar – will not bleed or stain
• External Above Ground – designed to meet the requirements of AS 4654-2012
System Components
• AQUAGARD™ M UVR – 1-part PU membrane
• AQUAGARD™ M Clear Primer – 1-part solvent based PU primer for dry cementitious, masonry, metal and timber substrates
• EPOCOTE™ F100W Clear – 2-part, water borne epoxy primer for green, damp or dry cementitious, masonry and metal substrates
• EPOCOTE™ F100W Grey – 2-part, water borne, filled epoxy primer for green, damp or dry cementitious, masonry and metal substrates, or poor quality/damaged concrete
• AQUAGARD™ M Non-Slip Top Coat – 2-part, solvent based, UV stable PU, protective top coat. Only used over exposed AQUAGARD™ M UVR membrane or in foot trafficable areas
• SILCOR® LM PU Sealant – 1-part polyurethane sealant for detailing and joint sealing
• Reinforcing PE Fabric Strip – Non-woven, needle punched polyester reinforcing fabric. For membrane reinforcement at high movement junctions
Compatibility / Adhesion
AQUAGARD™ M UVR may be applied to the following cured, stable, prepared and primed substrates:
• Concrete, blockwork, brick
• Cementitious screed, render or topping slabs
• Water resistant timber, plywood or particle board
• Metals
• Compressed fibre cement sheet (CFC)
• Cement composite sheet (CCS)
• Glass reinforced concrete (GRC)
• Rendered, aerated autoclaved concrete (AAC)
One-part polyurethane waterproofing membrane for horizontal applications
A one-part, liquid applied, high solids, polyurethane (PU) waterproofing membrane. It is formulated for simple, high build application to horizontal substrates. After application, the product cures through reaction with ambient humidity, forming a flexible, elastomeric membrane.
Advantages
• Seamless – liquid applied and monolithic, eliminating vulnerable joins, seams and laps
• Self-levelling – quick application
• Fully Bonded – no water tracking between membrane and substrate
• Simple Application – one-part, humidity cured. Applied by squeegee, roller or brush to horizontal surfaces
• Cold Applied – no flame or heat required for application
• Low VOC – reduced EH&S issues on site
• Flexible – long life elastomeric membrane. Accommodates normal structural movement and bridges non-structural concrete shrinkage cracks without requiring full membrane reinforcing
• Polyurethane Chemistry – free from bitumen or tar – will not bleed or stain
• External Above Ground – designed to meet the requirements of AS 4654-2012
System Components
• AQUAGARD™ M UVR – 1-part PU membrane
• AQUAGARD™ M Clear Primer – 1-part solvent based PU primer for dry cementitious, masonry, metal and timber substrates
• EPOCOTE™ F100W Clear – 2-part, water borne epoxy primer for green, damp or dry cementitious, masonry and metal substrates
• EPOCOTE™ F100W Grey – 2-part, water borne, filled epoxy primer for green, damp or dry cementitious, masonry and metal substrates, or poor quality/damaged concrete
• AQUAGARD™ M Non-Slip Top Coat – 2-part, solvent based, UV stable PU, protective top coat. Only used over exposed AQUAGARD™ M UVR membrane or in foot trafficable areas
• SILCOR® LM PU Sealant – 1-part polyurethane sealant for detailing and joint sealing
• Reinforcing PE Fabric Strip – Non-woven, needle punched polyester reinforcing fabric. For membrane reinforcement at high movement junctions
Compatibility / Adhesion
AQUAGARD™ M UVR may be applied to the following cured, stable, prepared and primed substrates:
• Concrete, blockwork, brick
• Cementitious screed, render or topping slabs
• Water resistant timber, plywood or particle board
• Metals
• Compressed fibre cement sheet (CFC)
• Cement composite sheet (CCS)
• Glass reinforced concrete (GRC)
• Rendered, aerated autoclaved concrete (AAC)
Australia
Hong Kong SAR
Indonesia
Malaysia
New Zealand
Philippines
Singapore
