BETEC™ FLX 120 is a fast curing, two-pack, polymer modified, tough cementicious waterproofing membrane. It is reinforced with specially graded synthetic fibre. When blended, BETEC FLX 120 forms a flexible matrix of rubber polymer and hydrate structures, providing a tough breathable membrane that is impermeable to liquid water. BETEC FLX 120 is easily applied as slurry onto horizontal and vertical surfaces.
Product Features
• Complies with Green Star requirements - has very low VOC level
• No toxic or hazardous ingredients
• Water clean-up and low odour
• Environmentally friendly
• Simple application and fast cure
• Resists continuous water immersion
• Self-priming and non-staining
• Total adhesion - no water tracking
• Hardwearing - long life
• Compatible with cement based tile adhesives
• Crack bridging ability
• Multi-purpose high build
Preparation
Surfaces to be sound, smooth and free from dust, loose matter, oil, grease or other contaminants. All surface defects shall be repaired using CHEMBOND™ modified mortar.
Use SILCOR® LM PU sealant to fill joints, cracks and form fillets to all internal corners or penetrations and allow to fully cure a minimum 24 hrs before applying BETEC FLX 120.
Mixing
• Pour Part B (liquid) into a clean container. Stir with a low-speed, heavy-duty drill fitted with a paddle mixer.
• Pour Part A (powder) slowly into Part B and mix to a uniform consistency.
• Avoid lump formation during mixing and move paddle up and down in the mix. Check for any unmixed powder at the bottom of the container.
• Use the clean plastic pails supplied as product packaging for mixing containers.
Bond Breaker
Use SILCOR LM PU sealant to form a 12mm angle in accordance with NCC as detailed by AS3740 and AS4654 for Class III waterproof membrane. Allow PU sealant to cure a min. 24 hours before proceeding with membrane installation.
Application
• Pre-dampen all porous substrates with clean water prior to application. Remove any ponded water.
• Waterproof Membrane – Apply mixed slurry by broad soft brush, roller or broom in at least 2 layers, each in a cross direction to the other – min. 1.25mm Dry Film Thickness (DFT).
• Anti-Efflorescence Sealer – Apply BETEC FLX 120 uniformly in one or two coats to achieve min. 1.0 mm DFT.
• Allow to dry thoroughly between coats.
• Always apply BETEC FLX 120 membrane on the side of the substrate that will be subject to hydrostatic pressure.
NOTE
• Seal high stress areas such as structural cracks, joints, penetrations and floor wastes, with Reinforcing Fabric PE embedded between two heavy layers of NEWFLEX™ Grey . Allow this detail to fully cure before applying BETEC FLX 120 system.
• Protect freshly applied BETEC FLX 120 membrane from site damage and exposure to heavy rain for 12 hours.
• Avoid applying BETEC FLX 120 under conditions of strong sunlight. Do not apply BETEC FLX 120 to very hot, dry substrates – re-dampen with water if necessary.
Surfacing
BETEC FLX 120 membrane is foot trafficable for surfacing/tiling within 8 hours. Use the following systems for specific situations as listed. Apply surfacing materials only to fully cured BETEC FLX 120.
• Tanking
Cover with PROTECTOBOARD™, PROTECTOBOARD™ HS or RAPID DRAIN™, followed by backfill or landscaping as required.
Rigid Surfaces
Use two layers of 0.2 mm PE slip-sheet with concrete topping. Paving slabs may be installed with a cement mortar bed or laid on sand. Ceramic tiles may be laid on bedding or directly fixed with polymer-modified cement-based adhesive. CHEMBOND™ polymer modified render or acrylic based textures may be applied directly to cured BETEC FLX 120.
BETEC™ FLX 120 is a fast curing, two-pack, polymer modified, tough cementicious waterproofing membrane. It is reinforced with specially graded synthetic fibre. When blended, BETEC FLX 120 forms a flexible matrix of rubber polymer and hydrate structures, providing a tough breathable membrane that is impermeable to liquid water. BETEC FLX 120 is easily applied as slurry onto horizontal and vertical surfaces.
Product Features
• Complies with Green Star requirements - has very low VOC level
• No toxic or hazardous ingredients
• Water clean-up and low odour
• Environmentally friendly
• Simple application and fast cure
• Resists continuous water immersion
• Self-priming and non-staining
• Total adhesion - no water tracking
• Hardwearing - long life
• Compatible with cement based tile adhesives
• Crack bridging ability
• Multi-purpose high build
Preparation
Surfaces to be sound, smooth and free from dust, loose matter, oil, grease or other contaminants. All surface defects shall be repaired using CHEMBOND™ modified mortar.
Use SILCOR® LM PU sealant to fill joints, cracks and form fillets to all internal corners or penetrations and allow to fully cure a minimum 24 hrs before applying BETEC FLX 120.
Mixing
• Pour Part B (liquid) into a clean container. Stir with a low-speed, heavy-duty drill fitted with a paddle mixer.
• Pour Part A (powder) slowly into Part B and mix to a uniform consistency.
• Avoid lump formation during mixing and move paddle up and down in the mix. Check for any unmixed powder at the bottom of the container.
• Use the clean plastic pails supplied as product packaging for mixing containers.
Bond Breaker
Use SILCOR LM PU sealant to form a 12mm angle in accordance with NCC as detailed by AS3740 and AS4654 for Class III waterproof membrane. Allow PU sealant to cure a min. 24 hours before proceeding with membrane installation.
Application
• Pre-dampen all porous substrates with clean water prior to application. Remove any ponded water.
• Waterproof Membrane – Apply mixed slurry by broad soft brush, roller or broom in at least 2 layers, each in a cross direction to the other – min. 1.25mm Dry Film Thickness (DFT).
• Anti-Efflorescence Sealer – Apply BETEC FLX 120 uniformly in one or two coats to achieve min. 1.0 mm DFT.
• Allow to dry thoroughly between coats.
• Always apply BETEC FLX 120 membrane on the side of the substrate that will be subject to hydrostatic pressure.
NOTE
• Seal high stress areas such as structural cracks, joints, penetrations and floor wastes, with Reinforcing Fabric PE embedded between two heavy layers of NEWFLEX™ Grey . Allow this detail to fully cure before applying BETEC FLX 120 system.
• Protect freshly applied BETEC FLX 120 membrane from site damage and exposure to heavy rain for 12 hours.
• Avoid applying BETEC FLX 120 under conditions of strong sunlight. Do not apply BETEC FLX 120 to very hot, dry substrates – re-dampen with water if necessary.
Surfacing
BETEC FLX 120 membrane is foot trafficable for surfacing/tiling within 8 hours. Use the following systems for specific situations as listed. Apply surfacing materials only to fully cured BETEC FLX 120.
• Tanking
Cover with PROTECTOBOARD™, PROTECTOBOARD™ HS or RAPID DRAIN™, followed by backfill or landscaping as required.
Rigid Surfaces
Use two layers of 0.2 mm PE slip-sheet with concrete topping. Paving slabs may be installed with a cement mortar bed or laid on sand. Ceramic tiles may be laid on bedding or directly fixed with polymer-modified cement-based adhesive. CHEMBOND™ polymer modified render or acrylic based textures may be applied directly to cured BETEC FLX 120.
BETEC™ FLX 120 is a fast curing, two-pack, polymer modified, tough cementicious waterproofing membrane. It is reinforced with specially graded synthetic fibre. When blended, BETEC FLX 120 forms a flexible matrix of rubber polymer and hydrate structures, providing a tough breathable membrane that is impermeable to liquid water. BETEC FLX 120 is easily applied as slurry onto horizontal and vertical surfaces.
Product Features
• Complies with Green Star requirements - has very low VOC level
• No toxic or hazardous ingredients
• Water clean-up and low odour
• Environmentally friendly
• Simple application and fast cure
• Resists continuous water immersion
• Self-priming and non-staining
• Total adhesion - no water tracking
• Hardwearing - long life
• Compatible with cement based tile adhesives
• Crack bridging ability
• Multi-purpose high build
Preparation
Surfaces to be sound, smooth and free from dust, loose matter, oil, grease or other contaminants. All surface defects shall be repaired using CHEMBOND™ modified mortar.
Use SILCOR® LM PU sealant to fill joints, cracks and form fillets to all internal corners or penetrations and allow to fully cure a minimum 24 hrs before applying BETEC FLX 120.
Mixing
• Pour Part B (liquid) into a clean container. Stir with a low-speed, heavy-duty drill fitted with a paddle mixer.
• Pour Part A (powder) slowly into Part B and mix to a uniform consistency.
• Avoid lump formation during mixing and move paddle up and down in the mix. Check for any unmixed powder at the bottom of the container.
• Use the clean plastic pails supplied as product packaging for mixing containers.
Bond Breaker
Use SILCOR LM PU sealant to form a 12mm angle in accordance with NCC as detailed by AS3740 and AS4654 for Class III waterproof membrane. Allow PU sealant to cure a min. 24 hours before proceeding with membrane installation.
Application
• Pre-dampen all porous substrates with clean water prior to application. Remove any ponded water.
• Waterproof Membrane – Apply mixed slurry by broad soft brush, roller or broom in at least 2 layers, each in a cross direction to the other – min. 1.25mm Dry Film Thickness (DFT).
• Anti-Efflorescence Sealer – Apply BETEC FLX 120 uniformly in one or two coats to achieve min. 1.0 mm DFT.
• Allow to dry thoroughly between coats.
• Always apply BETEC FLX 120 membrane on the side of the substrate that will be subject to hydrostatic pressure.
NOTE
• Seal high stress areas such as structural cracks, joints, penetrations and floor wastes, with Reinforcing Fabric PE embedded between two heavy layers of NEWFLEX™ Grey . Allow this detail to fully cure before applying BETEC FLX 120 system.
• Protect freshly applied BETEC FLX 120 membrane from site damage and exposure to heavy rain for 12 hours.
• Avoid applying BETEC FLX 120 under conditions of strong sunlight. Do not apply BETEC FLX 120 to very hot, dry substrates – re-dampen with water if necessary.
Surfacing
BETEC FLX 120 membrane is foot trafficable for surfacing/tiling within 8 hours. Use the following systems for specific situations as listed. Apply surfacing materials only to fully cured BETEC FLX 120.
• Tanking
Cover with PROTECTOBOARD™, PROTECTOBOARD™ HS or RAPID DRAIN™, followed by backfill or landscaping as required.
Rigid Surfaces
Use two layers of 0.2 mm PE slip-sheet with concrete topping. Paving slabs may be installed with a cement mortar bed or laid on sand. Ceramic tiles may be laid on bedding or directly fixed with polymer-modified cement-based adhesive. CHEMBOND™ polymer modified render or acrylic based textures may be applied directly to cured BETEC FLX 120.