- Hong Kong SAR
Pushbutton with thermostat and card holder
Energy Efficient
$ Cost Effective
Italy
CODE: EK-E13-TP-.. | EK-TH2-TP Pushbutton with thermostat and card holder for 2-fold plate (60x45 mm module) The 4-fold pushbutton of Ekinex® 71 series commands loads on/off switching, controls the dimming of lighting devices, controls motor drives for shutters or executes any other programmable command and control function. Thanks to the integrated temperature sensor, the pushbutton can work as a thermostat for a room or a zone. The LED can be chosen in the colour combinations blue / green or white / red. The device integrates a KNX bus communication module and is intended for mounting onto a wall mounting box; it is powered by a SELV voltage directly from the KNX bus and does not require any auxiliary power supply. Functions / Features: - Pushbutton - 4-fold (possibility to configure up to 8 independent functions) - 4 freely programmable LED for each channel - 2 colour combination available for the LED (blue / green or red / white) - Room thermostat function - Integrated temperature sensor - Plastic casing - Connection to bus line with KNX terminal block - Frontal programming pushbutton and LED - Wall-mounting installation on round or square wall box - IP20 protection degree (installed) - Weight 70 g (with mounting support) Card holder: - Presence detection via bus and communication to supervisory system via KNX TP bus (twisted pair) - Presence enabling after insertion of card in front pocket - Accommodation guest management based on reservation and check-in/check-out period; service user management based on time slots and passe-partout - Programmable output based on card validation or as actuator activated by KNX telegrams Delay on card withdrawal configurable for courtesy light management - Binary input available for connection of conventional push button (with switching, dimming or roller shutter/shutter function) or signalling contact (e.g. window opening) - Front white LED: flashing signal when card not inserted, off when card inserted; LED control via KNX bus telegrams possible - Notification of detected presence events to supervisory system with memory buffer - Plastic case - Connection to bus line via KNX terminal - Recessed wall mounting on round box - Degree of protection IP20 (installed) - Weight approx. 50 g (with mounting bracket)
CODE: EK-E13-TP-.. | EK-TH2-TP Pushbutton with thermostat and card holder for 2-fold plate (60x45 mm module) The 4-fold pushbutton of Ekinex® 71 series commands loads on/off switching, controls the dimming of lighting devices, controls motor drives for shutters or executes any other programmable command and control function. Thanks to the integrated temperature sensor, the pushbutton can work as a thermostat for a room or a zone. The LED can be chosen in the colour combinations blue / green or white / red. The device integrates a KNX bus communication module and is intended for mounting onto a wall mounting box; it is powered by a SELV voltage directly from the KNX bus and does not require any auxiliary power supply. Functions / Features: - Pushbutton - 4-fold (possibility to configure up to 8 independent functions) - 4 freely programmable LED for each channel - 2 colour combination available for the LED (blue / green or red / white) - Room thermostat function - Integrated temperature sensor - Plastic casing - Connection to bus line with KNX terminal block - Frontal programming pushbutton and LED - Wall-mounting installation on round or square wall box - IP20 protection degree (installed) - Weight 70 g (with mounting support) Card holder: - Presence detection via bus and communication to supervisory system via KNX TP bus (twisted pair) - Presence enabling after insertion of card in front pocket - Accommodation guest management based on reservation and check-in/check-out period; service user management based on time slots and passe-partout - Programmable output based on card validation or as actuator activated by KNX telegrams Delay on card withdrawal configurable for courtesy light management - Binary input available for connection of conventional push button (with switching, dimming or roller shutter/shutter function) or signalling contact (e.g. window opening) - Front white LED: flashing signal when card not inserted, off when card inserted; LED control via KNX bus telegrams possible - Notification of detected presence events to supervisory system with memory buffer - Plastic case - Connection to bus line via KNX terminal - Recessed wall mounting on round box - Degree of protection IP20 (installed) - Weight approx. 50 g (with mounting bracket)
CODE: EK-E13-TP-.. | EK-TH2-TP
Pushbutton with thermostat and card holder for 2-fold plate (60x45 mm module)
The 4-fold pushbutton of Ekinex® 71 series commands loads on/off switching, controls the dimming of lighting devices, controls motor drives for shutters or executes any other programmable command and control function. Thanks to the integrated temperature sensor, the pushbutton can work as a thermostat for a room or a zone. The LED can be chosen in the colour combinations blue / green or white / red. The device integrates a KNX bus communication module and is intended for mounting onto a wall mounting box; it is powered by a SELV voltage directly from the KNX bus and does not require any auxiliary power supply.
Functions / Features:
- Pushbutton
- 4-fold (possibility to configure up to 8 independent functions)
- 4 freely programmable LED for each channel
- 2 colour combination available for the LED (blue / green or red / white)
- Room thermostat function
- Integrated temperature sensor
- Plastic casing
- Connection to bus line with KNX terminal block
- Frontal programming pushbutton and LED
- Wall-mounting installation on round or square wall box
- IP20 protection degree (installed)
- Weight 70 g (with mounting support)
Card holder:
- Presence detection via bus and communication to supervisory system via KNX TP bus (twisted pair)
- Presence enabling after insertion of card in front pocket
- Accommodation guest management based on reservation and check-in/check-out period; service user management based on time slots and passe-partout
- Programmable output based on card validation or as actuator activated by KNX telegrams Delay on card withdrawal configurable for courtesy light management
- Binary input available for connection of conventional push button (with switching, dimming or roller shutter/shutter function) or signalling contact (e.g. window opening)
- Front white LED: flashing signal when card not inserted, off when card inserted; LED control via KNX bus telegrams possible
- Notification of detected presence events to supervisory system with memory buffer
- Plastic case
- Connection to bus line via KNX terminal
- Recessed wall mounting on round box
- Degree of protection IP20 (installed)
- Weight approx. 50 g (with mounting bracket)
Pushbutton with thermostat and card holder for 2-fold plate (60x45 mm module)
The 4-fold pushbutton of Ekinex® 71 series commands loads on/off switching, controls the dimming of lighting devices, controls motor drives for shutters or executes any other programmable command and control function. Thanks to the integrated temperature sensor, the pushbutton can work as a thermostat for a room or a zone. The LED can be chosen in the colour combinations blue / green or white / red. The device integrates a KNX bus communication module and is intended for mounting onto a wall mounting box; it is powered by a SELV voltage directly from the KNX bus and does not require any auxiliary power supply.
Functions / Features:
- Pushbutton
- 4-fold (possibility to configure up to 8 independent functions)
- 4 freely programmable LED for each channel
- 2 colour combination available for the LED (blue / green or red / white)
- Room thermostat function
- Integrated temperature sensor
- Plastic casing
- Connection to bus line with KNX terminal block
- Frontal programming pushbutton and LED
- Wall-mounting installation on round or square wall box
- IP20 protection degree (installed)
- Weight 70 g (with mounting support)
Card holder:
- Presence detection via bus and communication to supervisory system via KNX TP bus (twisted pair)
- Presence enabling after insertion of card in front pocket
- Accommodation guest management based on reservation and check-in/check-out period; service user management based on time slots and passe-partout
- Programmable output based on card validation or as actuator activated by KNX telegrams Delay on card withdrawal configurable for courtesy light management
- Binary input available for connection of conventional push button (with switching, dimming or roller shutter/shutter function) or signalling contact (e.g. window opening)
- Front white LED: flashing signal when card not inserted, off when card inserted; LED control via KNX bus telegrams possible
- Notification of detected presence events to supervisory system with memory buffer
- Plastic case
- Connection to bus line via KNX terminal
- Recessed wall mounting on round box
- Degree of protection IP20 (installed)
- Weight approx. 50 g (with mounting bracket)
General Specification
Colour | : | Black |
Product type | : | Switches |
Installation site | : | Recessed wall mounting |
Material | : | Plastic | Metal | Fenix |
Application | : | Hotel Solution | Room Control Unit RCU |
Size
Width | : | 160 mm |
Height | : | 80 mm |
Technical
Power | : | 30 Vdc power supply via KNX bus |
Auxiliary power supply | : | 12-24 Vac/dc |
Current consumption from bus | : | < 10 mA |
Other Products You Might Like
Other Products You Might Like