This paint is an anti-slip paint that is made by mixing epoxy resin and an excellent weather-resistant pigment, for which separately packed sand with good abrasion resistance is mixed for use.
This paint is excellent in the hardness of the film, abrasion resistance, impact resistance, oil resistance, adhesion, water resistance, flame resistance and workability. In particular, a super thick coating (5㎜) is possible by one coat, and it is widely used for new and repair painting on areas requiring slip prevention such as railings and stairs.
Surface treatment :
1. Cure concrete for at least 28 days at a temperature of 21℃ and a relative humidity of 50%.
2. Completely remove the oil, moisture, sand, dust, laitance and other foreign matter from the surface and maintain surface smoothness.
3. Reinforce grooves and crevices with epoxy putty and repair severe cracks with CLEANPOXY MORTAR DHDC-6500. Cut the expansion joint after completion of coating and fill with the NEW-THANSUNG SEAL(N).
4. Since the dense substrate to which the infiltration of undercoat is difficult causes poor adhesion with the intermediate coating due to the formation of the undercoat film on the surface of the substrate, a pretreatment needs to be done sufficiently before applying the primer so that it penetrates into the concrete and exerts excellent adhesion.
Coating conditions :
1. Atmosphere Temperature: 5~35℃, Surface Temperature: 40℃ or below, Relative Humidity: 80% or less, Moisture content in the concrete: 6% or less
2. Please note that due to the nature of epoxy paint, discoloration and chalking may occur if exposed to the outdoor environment.
3. The use of a thinner more than the recommended amount causes a further delay in drying, decline in hardness, whitening, skid marks, etc.
This paint is an anti-slip paint that is made by mixing epoxy resin and an excellent weather-resistant pigment, for which separately packed sand with good abrasion resistance is mixed for use.
This paint is excellent in the hardness of the film, abrasion resistance, impact resistance, oil resistance, adhesion, water resistance, flame resistance and workability. In particular, a super thick coating (5㎜) is possible by one coat, and it is widely used for new and repair painting on areas requiring slip prevention such as railings and stairs.
Surface treatment :
1. Cure concrete for at least 28 days at a temperature of 21℃ and a relative humidity of 50%.
2. Completely remove the oil, moisture, sand, dust, laitance and other foreign matter from the surface and maintain surface smoothness.
3. Reinforce grooves and crevices with epoxy putty and repair severe cracks with CLEANPOXY MORTAR DHDC-6500. Cut the expansion joint after completion of coating and fill with the NEW-THANSUNG SEAL(N).
4. Since the dense substrate to which the infiltration of undercoat is difficult causes poor adhesion with the intermediate coating due to the formation of the undercoat film on the surface of the substrate, a pretreatment needs to be done sufficiently before applying the primer so that it penetrates into the concrete and exerts excellent adhesion.
Coating conditions :
1. Atmosphere Temperature: 5~35℃, Surface Temperature: 40℃ or below, Relative Humidity: 80% or less, Moisture content in the concrete: 6% or less
2. Please note that due to the nature of epoxy paint, discoloration and chalking may occur if exposed to the outdoor environment.
3. The use of a thinner more than the recommended amount causes a further delay in drying, decline in hardness, whitening, skid marks, etc.
This paint is an anti-slip paint that is made by mixing epoxy resin and an excellent weather-resistant pigment, for which separately packed sand with good abrasion resistance is mixed for use.
This paint is excellent in the hardness of the film, abrasion resistance, impact resistance, oil resistance, adhesion, water resistance, flame resistance and workability. In particular, a super thick coating (5㎜) is possible by one coat, and it is widely used for new and repair painting on areas requiring slip prevention such as railings and stairs.
Surface treatment :
1. Cure concrete for at least 28 days at a temperature of 21℃ and a relative humidity of 50%.
2. Completely remove the oil, moisture, sand, dust, laitance and other foreign matter from the surface and maintain surface smoothness.
3. Reinforce grooves and crevices with epoxy putty and repair severe cracks with CLEANPOXY MORTAR DHDC-6500. Cut the expansion joint after completion of coating and fill with the NEW-THANSUNG SEAL(N).
4. Since the dense substrate to which the infiltration of undercoat is difficult causes poor adhesion with the intermediate coating due to the formation of the undercoat film on the surface of the substrate, a pretreatment needs to be done sufficiently before applying the primer so that it penetrates into the concrete and exerts excellent adhesion.
Coating conditions :
1. Atmosphere Temperature: 5~35℃, Surface Temperature: 40℃ or below, Relative Humidity: 80% or less, Moisture content in the concrete: 6% or less
2. Please note that due to the nature of epoxy paint, discoloration and chalking may occur if exposed to the outdoor environment.
3. The use of a thinner more than the recommended amount causes a further delay in drying, decline in hardness, whitening, skid marks, etc.