A one-part, liquid applied, high solids, polyurethane (PU) waterproofing membrane. It is formulated for simple, high build application to horizontal and vertical substrates. After application, the product cures through reaction with ambient humidity, forming a flexible, elastomeric membrane.
Advantages
• Seamless – liquid applied and monolithic, eliminating vulnerable joins, seams and laps
• Fully Bonded – no water tracking between membrane and substrate
• Simple Application – one-part, humidity cured. Applied by roller or brush to horizontal or vertical surfaces
• Cold Applied – no flame or heat required for application
• Low VOC – reduced EH&S issues on site
• Flexible – long life elastomeric membrane. Accommodates normal structural movement and bridges non-structural concrete shrinkage cracks without requiring full membrane reinforcing
• Polyurethane Chemistry – free from bitumen or tar – will not bleed or stain
• External Above Ground – designed to meet the requirements of AS 4654-2012
• Internal Wet Areas – designed to meet the requirements of AS 3740-2004
System Components
• AQUAGARD™ M 40R Charcoal – 1-part PU membrane
• AQUAGARD™ M Clear Primer – 1-part solvent based PU primer for dry cementitious, masonry, metal and timber substrates
• EPOCOTE™ F100W Clear – 2-part, water borne epoxy primer for green, damp or dry cementitious, masonry and metal substrates
• EPOCOTE™ F100W Grey – 2-part, water borne, filled epoxy primer for green, damp or dry cementitious, masonry and metal substrates, or poor quality/damaged concrete
• AQUAGARD™ M Non-Slip Top Coat – 2-part, solvent based, UV stable PU, protective top coat. Only used over
• AQUAGARD™ M 40R Charcoal membrane in non-trafficable areas
• SILCOR® LM PU Sealant – 1-part polyurethane sealant for detailing and joint sealing
• Reinforcing PE Fabric Strip – Non-woven, needle punched polyester reinforcing fabric. For membrane reinforcement at high movement junctions
Design
Generally, all horizontal substrates to have a minimum 1:100 fall to drainage and/or not retain water other than residual due to substrate surface tension.
Compatibility / Adhesion
AQUAGARD™ M 40R Charcoal may be applied to the following cured, stable, prepared and primed substrates:
• Concrete, blockwork, brick
• Cementitious screed, render or topping slabs
• Water resistant timber, plywood or particle board
• Metals
• Compressed fibre cement sheet (CFC)
• Cement composite sheet (CCS)
• Glass reinforced concrete (GRC)
• Rendered, aerated autoclaved concrete (AAC)
A one-part, liquid applied, high solids, polyurethane (PU) waterproofing membrane. It is formulated for simple, high build application to horizontal and vertical substrates. After application, the product cures through reaction with ambient humidity, forming a flexible, elastomeric membrane.
Advantages
• Seamless – liquid applied and monolithic, eliminating vulnerable joins, seams and laps
• Fully Bonded – no water tracking between membrane and substrate
• Simple Application – one-part, humidity cured. Applied by roller or brush to horizontal or vertical surfaces
• Cold Applied – no flame or heat required for application
• Low VOC – reduced EH&S issues on site
• Flexible – long life elastomeric membrane. Accommodates normal structural movement and bridges non-structural concrete shrinkage cracks without requiring full membrane reinforcing
• Polyurethane Chemistry – free from bitumen or tar – will not bleed or stain
• External Above Ground – designed to meet the requirements of AS 4654-2012
• Internal Wet Areas – designed to meet the requirements of AS 3740-2004
System Components
• AQUAGARD™ M 40R Charcoal – 1-part PU membrane
• AQUAGARD™ M Clear Primer – 1-part solvent based PU primer for dry cementitious, masonry, metal and timber substrates
• EPOCOTE™ F100W Clear – 2-part, water borne epoxy primer for green, damp or dry cementitious, masonry and metal substrates
• EPOCOTE™ F100W Grey – 2-part, water borne, filled epoxy primer for green, damp or dry cementitious, masonry and metal substrates, or poor quality/damaged concrete
• AQUAGARD™ M Non-Slip Top Coat – 2-part, solvent based, UV stable PU, protective top coat. Only used over
• AQUAGARD™ M 40R Charcoal membrane in non-trafficable areas
• SILCOR® LM PU Sealant – 1-part polyurethane sealant for detailing and joint sealing
• Reinforcing PE Fabric Strip – Non-woven, needle punched polyester reinforcing fabric. For membrane reinforcement at high movement junctions
Design
Generally, all horizontal substrates to have a minimum 1:100 fall to drainage and/or not retain water other than residual due to substrate surface tension.
Compatibility / Adhesion
AQUAGARD™ M 40R Charcoal may be applied to the following cured, stable, prepared and primed substrates:
• Concrete, blockwork, brick
• Cementitious screed, render or topping slabs
• Water resistant timber, plywood or particle board
• Metals
• Compressed fibre cement sheet (CFC)
• Cement composite sheet (CCS)
• Glass reinforced concrete (GRC)
• Rendered, aerated autoclaved concrete (AAC)
A one-part, liquid applied, high solids, polyurethane (PU) waterproofing membrane. It is formulated for simple, high build application to horizontal and vertical substrates. After application, the product cures through reaction with ambient humidity, forming a flexible, elastomeric membrane.
Advantages
• Seamless – liquid applied and monolithic, eliminating vulnerable joins, seams and laps
• Fully Bonded – no water tracking between membrane and substrate
• Simple Application – one-part, humidity cured. Applied by roller or brush to horizontal or vertical surfaces
• Cold Applied – no flame or heat required for application
• Low VOC – reduced EH&S issues on site
• Flexible – long life elastomeric membrane. Accommodates normal structural movement and bridges non-structural concrete shrinkage cracks without requiring full membrane reinforcing
• Polyurethane Chemistry – free from bitumen or tar – will not bleed or stain
• External Above Ground – designed to meet the requirements of AS 4654-2012
• Internal Wet Areas – designed to meet the requirements of AS 3740-2004
System Components
• AQUAGARD™ M 40R Charcoal – 1-part PU membrane
• AQUAGARD™ M Clear Primer – 1-part solvent based PU primer for dry cementitious, masonry, metal and timber substrates
• EPOCOTE™ F100W Clear – 2-part, water borne epoxy primer for green, damp or dry cementitious, masonry and metal substrates
• EPOCOTE™ F100W Grey – 2-part, water borne, filled epoxy primer for green, damp or dry cementitious, masonry and metal substrates, or poor quality/damaged concrete
• AQUAGARD™ M Non-Slip Top Coat – 2-part, solvent based, UV stable PU, protective top coat. Only used over
• AQUAGARD™ M 40R Charcoal membrane in non-trafficable areas
• SILCOR® LM PU Sealant – 1-part polyurethane sealant for detailing and joint sealing
• Reinforcing PE Fabric Strip – Non-woven, needle punched polyester reinforcing fabric. For membrane reinforcement at high movement junctions
Design
Generally, all horizontal substrates to have a minimum 1:100 fall to drainage and/or not retain water other than residual due to substrate surface tension.
Compatibility / Adhesion
AQUAGARD™ M 40R Charcoal may be applied to the following cured, stable, prepared and primed substrates:
• Concrete, blockwork, brick
• Cementitious screed, render or topping slabs
• Water resistant timber, plywood or particle board
• Metals
• Compressed fibre cement sheet (CFC)
• Cement composite sheet (CCS)
• Glass reinforced concrete (GRC)
• Rendered, aerated autoclaved concrete (AAC)