- Malaysia
JOE PU FOAM ADHESIVE
Characteristics : - Sound and heat insulation, bonding, fixing and sealing. - Processing temperature (can and environment) between +5ºC ~ +35ºC. Optimum processing temperature between +18ºC ~ +25ºC. Range of temperature resistance of cured foam is from -30ºC ~ +80ºC. - The foam will adhere to materials such as concrete slab, concrete wall panels, masonry, metal, wood, and plastic except teflon and silicone. Cured foam is non-toxic. - Fast curing. - Reduce smoke emission. - Foam expansion 50-60 times. - Filling unreachable area and big gaps. - Insulating and noise barrier properties. - High grade fire retardant and self extinguish. Cuttable after 60 minutes and apply with finishes. Directions : - Wear protective gloves, goggles and work clothes during use. - Clean surfaces from oil, grease, dirt, dust and loose particles, then premoisten the cavity. Dry surfaces should be well sprayed or dampended with water. - Use between 5ºC ~ 35ºC. - Shake can for 1 minute vigorously before use. - Tack off cap, firmly screw gun into the can. Turn the flow adjustment screw. - Hold can UPSIDE DOWN with tube pointing into far end of cavity, slowly press trigger to dispense foam. - Fill vertical gaps from the bottom up. - Fill cavity 50% with foam to allow for expansion. - Use PU Foam Cleaner to remove excess uncured foam on nozzle and valve. - Take free time 10 - 20 minutes. The foam can be cut using a knife after 60 minutes. It will cured after 1 hour and is stable within 3 - 5 hours. - Cured foam can be trimmed, painted, skim coated, sanded, plastered, grouted or caulked. - The foam discharge rate can be regulated with the trigger and controlled with the flow adjustment screw. Turn it off clockwise direction when finish. Before replacing, shake a new foam can vigorously for 1 minute, unscrew empty can and immediately replace with the new foam can. Applications : - Adhesive for concrete wall panel joints to structural members, deflection and crack control purposes. - Seals around installation of switches and sockets, gap between wall and air-conditioner wall, exhaust fan, filling and sealing gaps between wall and pipes. - Fills cracks and joints, cavities, gaps around pipes, vents, utility lines, electrical outlets, seals around windows, doors, siding and baseboard. - Seals and insulates joint and gap between sole plate and concrete slab / wall panels.
Characteristics : - Sound and heat insulation, bonding, fixing and sealing. - Processing temperature (can and environment) between +5ºC ~ +35ºC. Optimum processing temperature between +18ºC ~ +25ºC. Range of temperature resistance of cured foam is from -30ºC ~ +80ºC. - The foam will adhere to materials such as concrete slab, concrete wall panels, masonry, metal, wood, and plastic except teflon and silicone. Cured foam is non-toxic. - Fast curing. - Reduce smoke emission. - Foam expansion 50-60 times. - Filling unreachable area and big gaps. - Insulating and noise barrier properties. - High grade fire retardant and self extinguish. Cuttable after 60 minutes and apply with finishes. Directions : - Wear protective gloves, goggles and work clothes during use. - Clean surfaces from oil, grease, dirt, dust and loose particles, then premoisten the cavity. Dry surfaces should be well sprayed or dampended with water. - Use between 5ºC ~ 35ºC. - Shake can for 1 minute vigorously before use. - Tack off cap, firmly screw gun into the can. Turn the flow adjustment screw. - Hold can UPSIDE DOWN with tube pointing into far end of cavity, slowly press trigger to dispense foam. - Fill vertical gaps from the bottom up. - Fill cavity 50% with foam to allow for expansion. - Use PU Foam Cleaner to remove excess uncured foam on nozzle and valve. - Take free time 10 - 20 minutes. The foam can be cut using a knife after 60 minutes. It will cured after 1 hour and is stable within 3 - 5 hours. - Cured foam can be trimmed, painted, skim coated, sanded, plastered, grouted or caulked. - The foam discharge rate can be regulated with the trigger and controlled with the flow adjustment screw. Turn it off clockwise direction when finish. Before replacing, shake a new foam can vigorously for 1 minute, unscrew empty can and immediately replace with the new foam can. Applications : - Adhesive for concrete wall panel joints to structural members, deflection and crack control purposes. - Seals around installation of switches and sockets, gap between wall and air-conditioner wall, exhaust fan, filling and sealing gaps between wall and pipes. - Fills cracks and joints, cavities, gaps around pipes, vents, utility lines, electrical outlets, seals around windows, doors, siding and baseboard. - Seals and insulates joint and gap between sole plate and concrete slab / wall panels.
Characteristics :
- Sound and heat insulation, bonding, fixing and sealing.
- Processing temperature (can and environment) between +5ºC ~ +35ºC. Optimum processing temperature between +18ºC ~ +25ºC. Range of temperature resistance of cured foam is from -30ºC ~ +80ºC.
- The foam will adhere to materials such as concrete slab, concrete wall panels, masonry, metal, wood, and plastic except teflon and silicone. Cured foam is non-toxic.
- Fast curing.
- Reduce smoke emission.
- Foam expansion 50-60 times.
- Filling unreachable area and big gaps.
- Insulating and noise barrier properties.
- High grade fire retardant and self extinguish. Cuttable after 60 minutes and apply with finishes.
Directions :
- Wear protective gloves, goggles and work clothes during use.
- Clean surfaces from oil, grease, dirt, dust and loose particles, then premoisten the cavity. Dry surfaces should be well sprayed or dampended with water.
- Use between 5ºC ~ 35ºC.
- Shake can for 1 minute vigorously before use.
- Tack off cap, firmly screw gun into the can. Turn the flow adjustment screw.
- Hold can UPSIDE DOWN with tube pointing into far end of cavity, slowly press trigger to dispense foam.
- Fill vertical gaps from the bottom up.
- Fill cavity 50% with foam to allow for expansion.
- Use PU Foam Cleaner to remove excess uncured foam on nozzle and valve.
- Take free time 10 - 20 minutes. The foam can be cut using a knife after 60 minutes. It will cured after 1 hour and is stable within 3 - 5 hours.
- Cured foam can be trimmed, painted, skim coated, sanded, plastered, grouted or caulked.
- The foam discharge rate can be regulated with the trigger and controlled with the flow adjustment screw. Turn it off clockwise direction when finish. Before replacing, shake a new foam can vigorously for 1 minute, unscrew empty can and immediately replace with the new foam can.
Applications :
- Adhesive for concrete wall panel joints to structural members, deflection and crack control purposes.
- Seals around installation of switches and sockets, gap between wall and air-conditioner wall, exhaust fan, filling and sealing gaps between wall and pipes.
- Fills cracks and joints, cavities, gaps around pipes, vents, utility lines, electrical outlets, seals around windows, doors, siding and baseboard.
- Seals and insulates joint and gap between sole plate and concrete slab / wall panels.
- Sound and heat insulation, bonding, fixing and sealing.
- Processing temperature (can and environment) between +5ºC ~ +35ºC. Optimum processing temperature between +18ºC ~ +25ºC. Range of temperature resistance of cured foam is from -30ºC ~ +80ºC.
- The foam will adhere to materials such as concrete slab, concrete wall panels, masonry, metal, wood, and plastic except teflon and silicone. Cured foam is non-toxic.
- Fast curing.
- Reduce smoke emission.
- Foam expansion 50-60 times.
- Filling unreachable area and big gaps.
- Insulating and noise barrier properties.
- High grade fire retardant and self extinguish. Cuttable after 60 minutes and apply with finishes.
Directions :
- Wear protective gloves, goggles and work clothes during use.
- Clean surfaces from oil, grease, dirt, dust and loose particles, then premoisten the cavity. Dry surfaces should be well sprayed or dampended with water.
- Use between 5ºC ~ 35ºC.
- Shake can for 1 minute vigorously before use.
- Tack off cap, firmly screw gun into the can. Turn the flow adjustment screw.
- Hold can UPSIDE DOWN with tube pointing into far end of cavity, slowly press trigger to dispense foam.
- Fill vertical gaps from the bottom up.
- Fill cavity 50% with foam to allow for expansion.
- Use PU Foam Cleaner to remove excess uncured foam on nozzle and valve.
- Take free time 10 - 20 minutes. The foam can be cut using a knife after 60 minutes. It will cured after 1 hour and is stable within 3 - 5 hours.
- Cured foam can be trimmed, painted, skim coated, sanded, plastered, grouted or caulked.
- The foam discharge rate can be regulated with the trigger and controlled with the flow adjustment screw. Turn it off clockwise direction when finish. Before replacing, shake a new foam can vigorously for 1 minute, unscrew empty can and immediately replace with the new foam can.
Applications :
- Adhesive for concrete wall panel joints to structural members, deflection and crack control purposes.
- Seals around installation of switches and sockets, gap between wall and air-conditioner wall, exhaust fan, filling and sealing gaps between wall and pipes.
- Fills cracks and joints, cavities, gaps around pipes, vents, utility lines, electrical outlets, seals around windows, doors, siding and baseboard.
- Seals and insulates joint and gap between sole plate and concrete slab / wall panels.
General Specification
Usage | : | Masonry |
Usage option | : | Concrete wall panels |
Size
Product size | : | Contact us for more details |
Collection
Other Products You Might Like